CAD (0) ▾
  • Cart is empty
  1. Request CAD files
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 39000

Cone Part Number

 N/A 39236

Cup Part Number

 N/A 39414X

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.3617 in59.987 mm

D - Cup Outer Diameter

 N/A 4.1339 in105.001 mm

B - Cone Width

 N/A 0.8661 in21.999 mm

C - Cup Width

 N/A 0.6299 in15.999 mm

T - Bearing Width

 N/A 0.8661 in21.999 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.08 in2.03 mm

da - Cone Frontface Backing Diameter

 N/A 2.64 in67 mm

db - Cone Backface Backing Diameter

 N/A 2.8 in71 mm

Da - Cup Frontface Backing Diameter

 N/A 3.96 in100.10 mm

Db - Cup Backface Backing Diameter

 N/A 3.78 in96.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.05 in1.3 mm
a - Effective Center Location3 N/A -0.06 in-1.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 6680 lbf29700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 25800 lbf115000 N

C0 - Static Radial Rating

 N/A 27000 lbf120000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 4440 lbf19700 N

Factors

K - Factor7 N/A 1.51
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.55

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 51.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 19.5
Cg - Geometry Factor10 N/A 0.0947
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.