CAD (0) ▾
  • Cart is empty
  1. Request CAD files
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 71000

Cone Part Number

 N/A 71373

Cup Part Number

 N/A 71788

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3.7381 in94.948 mm

D - Cup Outer Diameter

 N/A 7.8730 in199.974 mm

B - Cone Width

 N/A 1.9488 in49.500 mm

C - Cup Width

 N/A 1.4488 in36.800 mm

T - Bearing Width

 N/A 1.9488 in49.5 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.16 in4.1 mm
r - Cup Backface "To Clear" Radius2 N/A 0.16 in4.06 mm

da - Cone Frontface Backing Diameter

 N/A 4.33 in110 mm

db - Cone Backface Backing Diameter

 N/A 4.65 in118 mm

Da - Cup Frontface Backing Diameter

 N/A 7.17 in182.12 mm

Db - Cup Backface Backing Diameter

 N/A 6.85 in173.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.09 in2.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.18 in4.6 mm
a - Effective Center Location3 N/A -0.26 in-6.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 21200 lbf94300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 81700 lbf364000 N

C0 - Static Radial Rating

 N/A 122000 lbf543000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 15100 lbf67100 N

Factors

K - Factor7 N/A 1.4
e - ISO Factor8 N/A 0.42
Y - ISO Factor9 N/A 1.44

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 269.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 49.5
Cg - Geometry Factor10 N/A 0.116
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.