CAD (0) ▾
  • Cart is empty
  1. Request CAD files
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 670000

Cone Part Number

 N/A EE671801

Cup Part Number

 N/A 672873

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE671801-90016 EE671801-90025

Dimensions

d - Bore

 N/A 18.0000 in457.200 mm

D - Cup Outer Diameter

 N/A 28.7460 in730.148 mm

B - Cone Width

 N/A 4.5000 in114.300 mm

C - Cup Width

 N/A 3.25 in82.55 mm

T - Bearing Width

 N/A 4.7500 in120.650 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in9.700 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 19.33 in491 mm

db - Cone Backface Backing Diameter

 N/A 19.96 in507 mm

Da - Cup Frontface Backing Diameter

 N/A 26.93 in680.50 mm

Db - Cup Backface Backing Diameter

 N/A 26.57 in674.88 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.54 in13.7 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.71 in18 mm
a - Effective Center Location3 N/A 0.21 in5.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 165000 lbf733000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 635000 lbf2830000 N

C0 - Static Radial Rating

 N/A 1100000 lbf4870000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 111000 lbf492000 N

Factors

K - Factor7 N/A 1.49
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.53

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 4970

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 343
Cg - Geometry Factor10 N/A 0.231
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.