CAD (0) ▾
  • Cart is empty
  1. Request CAD files
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Request Information
Unit of Measure

Specifications

Series

 N/A 920000

Cone Part Number

 N/A EE921124

Cup Part Number

 N/A 921850

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 11.2500 in285.750 mm

D - Cup Outer Diameter

 N/A 18.5000 in469.900 mm

B - Cone Width

 N/A 3.1720 in80.569 mm

C - Cup Width

 N/A 2.2500 in57.150 mm

T - Bearing Width

 N/A 3.2193 in81.770 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in9.700 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 12.17 in309 mm

db - Cone Backface Backing Diameter

 N/A 12.8 in325 mm

Da - Cup Frontface Backing Diameter

 N/A 17.33 in440.20 mm

Db - Cup Backface Backing Diameter

 N/A 17.28 in438.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.29 in7.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.58 in14.7 mm
a - Effective Center Location3 N/A -0.53 in-13.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 88000 lbf391000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 339000 lbf1510000 N

C0 - Static Radial Rating

 N/A 447000 lbf1990000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 44000 lbf196000 N

Factors

K - Factor7 N/A 2
e - ISO Factor8 N/A 0.29
Y - ISO Factor9 N/A 2.05

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1732.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 200
Cg - Geometry Factor10 N/A 0.148
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.