The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back
Hexact Linear Actuation Method
    The HLA adjustable pulley can be used in place of the standard “HM” pulley where an external mechanical control is available. Typical control methods include hydraulic cylinder, air cylinder, and lever. The adapter nut located on the end of the HLA pulley will accept a threaded rod or a clevis with cross pins. The actuator linkage must be on the center line of the pulley, but radial freedom is required to relieve loads caused by misalignment of the linkage. Actuation rate (closing the moveable flange) should not exceed 2-1/2 inches per minute.

    To specify the correct pulley, simply substitute the HLA prefix for the HM. For example, the Model HLA-7 pulley has the same drive characteristics as the Model HM-7 hand wheel-type pulley. Refer to the adjacent chart for dimensional information. A torque arm bracket is NOT required for the HLA drive.
Hexadrive HLA Series Adjustable Pulleys w/ Hexact Linear Actuation Method
HLA Pulley Actuation Recommendations
Unit of Measure
Items Hexadrive HLA Series Adjustable Pulleys w/ Hexact Linear Actuation Method
68514442927
Hexadrive Series Model HLA-30 Adjustable Pulleys w/ Hexact Linear Actuation Method - Imperial 		Hexadrive HLA Series Adjustable Pulleys w/ Hexact Linear Actuation Method
68514442928
Hexadrive Series Model HLA-30 Adjustable Pulleys w/ Hexact Linear Actuation Method - Imperial 		Hexadrive HLA Series Adjustable Pulleys w/ Hexact Linear Actuation Method
68514442929
Hexadrive Series Model HLA-30 Adjustable Pulleys w/ Hexact Linear Actuation Method - Imperial 		Hexadrive HLA Series Adjustable Pulleys w/ Hexact Linear Actuation Method
68514442930
Hexadrive Series Model HLA-30 Adjustable Pulleys w/ Hexact Linear Actuation Method - Imperial
Description  N/A HLA-30-1-3/8-PULLEY N/A HLA-30-1-5/8-PULLEY N/A HLA-30-1-7/8-PULLEY N/A HLA-30-2-1/8-PULLEY
Bore Diameter  N/A 1 3/8 in N/A 1 5/8 in N/A 1 7/8 in N/A 2 1/8 in
Model N/A HLA-30
Type N/A Adjustable Center - Driver
Belt Size N/A 4430V
Outside Diameter (Dimension A) N/A 12.500 in
Belt Top Width (Dimension B) N/A 2.750 in
Dimension C N/A 0.780 in19.81 mm
Distance at Min. PD (Dimension D) N/A 5.190 in
Bore Depth (Dimension E) N/A 7.500 in
Max. Opening Distance (Dimension F) N/A 12.830 in
Min. Opening Distance (Dimension G) N/A 10.810 in
Thru Hole (Dimension H) N/A 0.390 in
Distance Across Flats (Dimension I) N/A 1.480 in
Nut Diameter (Dimension J) N/A 1.570 in
Max. Thrust (Dimension K) N/A 1015.00 lb
Diameter (Dimension L) N/A 4.500 in
Thread (Dimension M) N/A 3/4-10 UNC
Max. Depth (Dimension N) N/A 0.87 in Diameter x 1.62 in
Flat Length (Dimension P) N/A 1.000 in
Dimension R N/A 1.120 in28.45 mm
Max. Depth (Dimension S) N/A 3.000 in
Weight N/A 46.00 lb
UPC Number N/A 42927 N/A 42928 N/A 42929 N/A 42930
Cubic inches N/A 2004.68750 in³