COMPANY HEADER
Print Back
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
Unit of Measure

Specifications

Series

 N/A 28500

Cone Part Number

 N/A 28584

Cup Part Number

 N/A 28521-B

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 28584-90024

Dimensions

d - Bore

 N/A 2.0625 in

D - Cup Outer Diameter

 N/A 3.6250 in

D1 - Flange Outer Diameter

 N/A 3.7772 in

B - Cone Width

 N/A 1.0000 in

C - Cup Width

 N/A 0.7813 in

C1 - Cup Flange Width

 N/A 0.1562 in

T1 - Bearing Width to Flange

 N/A 0.3437 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in
r - Cup Backface "To Clear" Radius2 N/A 0.030 in

da - Cone Frontface Backing Diameter

 N/A 2.28 in

db - Cone Backface Backing Diameter

 N/A 2.56 in

Da - Cup Frontface Backing Diameter

 N/A 3.54 in

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in

Aa - Cage-Cone Backface Clearance

 N/A 0.04 in
a - Effective Center Location3 N/A -0.19 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 5770 lbf25700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 22200 lbf98900 N

C0 - Static Radial Rating

 N/A 29200 lbf130000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3720 lbf16600 N

Factors

K - Factor7 N/A 1.55
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.59

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 46.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 22.6
Cg - Geometry Factor10 N/A 0.0912
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.