The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back
  • Each assembly includes the housing cap and base, cap bolts, bearing, locknut and lockwasher, stabilizing ring and triple ring seals.
  • To order pillow block housing only, use the numbers listed in "Housing Only" column. These units include: cap, base, cap bolts, triple ring seals and stabilizing ring.
  • Assembly and pillow blocks described on this page constitute fixed units.
  • To order float units, specify part number plus suffix "Float" or "FL".
  • If one end closed assembly is required, specify “CL” in assembly number when ordering.
  • All assemblies shown are furnished in cast iron. If cast steel is desired, add the letter "S" to the alpha prefix (e.g., SAFS 22217).

Speed ratings are found in dimension tables in the spherical roller bearing section.
Unit of Measure

Specifications

Bearing Number

 N/A 22338

Diameter S-2

 N/A 8 3/8 in

Diameter S-3

 N/A 7.2500 in

A

 N/A 9.5 in

B

 N/A 32.75 in

C

 N/A 8.75 in

D

 N/A 3.75 in

E Max.

 N/A 27.875 in

E Min.

 N/A 24.75 in

F

 N/A 5.25 in
H1 N/A 19.625 in

Oil Level K

 N/A 3.6875 in
L2 N/A 11.5000 in

Y

 N/A 3.8906 in

No. of Base Bolts Required

 N/A 4

Size of Base Bolts Required

 N/A 1 1/2

Bolt Hole Length

 N/A 3.0625 in

Bolt Hole Width

 N/A 1.5 in

Locknut

 N/A AN38

Lockwasher

 N/A W38
Housing Only3 N/A SAF338
Stabilizing Ring 1 Req'd4 N/A SR-44-38

Triple Seal 2 Req’d at S-2

 N/A LOR171

Triple Seal 2 Req’d at S-3

 N/A LOR160

Seal Type

 N/A Triple Ring Seal

Full Timken Part Number

 N/A SAF22338

Basic Load Ratings

C0 - Static Radial Rating

 N/A 635000 lbf2830000 N

C1(2) - Dynamic Radial Rating (Two-Rows)

 N/A 534000 lbf2380000 N

Factors

e - ISO Factor5 N/A 0.32
Y0 - ISO Factor6 N/A 2.07
Y1 - ISO Factor7 N/A 2.12
Y2 - ISO Factor8 N/A 3.15

Reference Thermal Speed Rating (Grease)

 N/A 1100 rpm
Reference Thermal Speed Rating (Oil)9 N/A 1200 rpm
Cg - Geometry Factor10 N/A 0.1021
  • 1 Tolerance -0 to + 0.4 mm (-0 to +1/64 in)
  • 2 Tolerance -0 to + 0.4 mm (-0 to +1/64 in)
  • 3 "Housing Only" includes: cap, base, cap bolts, triple ring seals and stabilizing ring as required. When ordering non-standard housing only specify the shaft size.
  • 4 Stabilizing ring is used for fixed (FX) block; do not use for float (FL) mounting.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These factors apply for both inch and metric calculations. See engineering
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 See thermal speed ratings in the engineering section.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.