COMPANY HEADER
Print Back
The configuration of the TDO provides a wide effective bearing spread, making it ideal for applications in which overturning moments are a significant load component. TDO bearings can be used in fixed positions or allowed to float in the housing bore.
Unit of Measure

Specifications

Series

 N/A HM259000

Cone Part Number

 N/A HM259049

Cup Part Number

 N/A HM259010D

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 12 1/2 in

D - Cup Outer Diameter

 N/A 17.6250 in

B - Cone Width

 N/A 3.3750 in

C - Double Cup Width

 N/A 5.7500 in

T - Bearing Width across Cones

 N/A 7.1249 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in
r - Cup Backface "To Clear" Radius2 N/A 0.06 in

db - Cone Backface Backing Diameter

 N/A 13.43 in

Da - Cup Frontface Backing Diameter

 N/A 16.85 in

Aa - Cage-Cone Backface Clearance

 N/A 0.19 in
a - Effective Center Location3 N/A -0.19 in

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)4 N/A 97800 lbf435000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)5 N/A 656000 lbf2920000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)6 N/A 170000 lbf757000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 56000 lbf249000 N

Factors

K - Factor8 N/A 1.74
e - ISO Factor9 N/A 0.33
Y1 - ISO Factor10 N/A 2.02
Y2 - ISO Factor11 N/A 3
Cg - Geometry Factor12 N/A 0.186
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 12 Geometry constant for Lubrication Life Adjustment Factor a3l.