COMPANY HEADER
Print Back
The configuration of the TDO provides a wide effective bearing spread, making it ideal for applications in which overturning moments are a significant load component. TDO bearings can be used in fixed positions or allowed to float in the housing bore.
Unit of Measure

Specifications

Series

 N/A HM265000

Cone Part Number

 N/A HM265049

Cup Part Number

 N/A HM265010CD

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A HM265049-90062 HM265049-90068 HM265049-90071 HM265049-90084 HM265049-902A1 HM265049-902C9 HM265049-902D1 HM265049-902D2 HM265049-902D3 HM265049-902D6

Dimensions

d - Bore

 N/A 14.4980 in

D - Cup Outer Diameter

 N/A 20.6250 in

B - Cone Width

 N/A 4.0000 in

C - Double Cup Width

 N/A 6.6875 in

T - Bearing Width across Cones

 N/A 8.4374 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in
r - Cup Backface "To Clear" Radius2 N/A 0.06 in

db - Cone Backface Backing Diameter

 N/A 15.75 in

Da - Cup Frontface Backing Diameter

 N/A 19.67 in

Aa - Cage-Cone Backface Clearance

 N/A 0.3 in
a - Effective Center Location3 N/A -0.33 in

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)4 N/A 132000 lbf589000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)5 N/A 890000 lbf3960000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)6 N/A 231000 lbf1030000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 75400 lbf335000 N

Factors

K - Factor8 N/A 1.76
e - ISO Factor9 N/A 0.33
Y1 - ISO Factor10 N/A 2.03
Y2 - ISO Factor11 N/A 3.02
Cg - Geometry Factor12 N/A 0.211
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 12 Geometry constant for Lubrication Life Adjustment Factor a3l.