COMPANY HEADER
Print Back
The configuration of the TDO provides a wide effective bearing spread, making it ideal for applications in which overturning moments are a significant load component. TDO bearings can be used in fixed positions or allowed to float in the housing bore.
Unit of Measure

Specifications

Series

 N/A LM281800

Cone Part Number

 N/A LM281849

Cup Part Number

 N/A LM281810CD

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A LM281849-904A2 LM281849-904A3 LM281849-904A4 LM281849-904A8 LM281849-904A9 LM281849-904B1 LM281849-904B2

Dimensions

d - Bore

 N/A 26.7500 in

D - Cup Outer Diameter

 N/A 35.5000 in

B - Cone Width

 N/A 5.6250 in

C - Double Cup Width

 N/A 9.6250 in

T - Bearing Width across Cones

 N/A 12.1250 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in
r - Cup Backface "To Clear" Radius2 N/A 0.06 in

db - Cone Backface Backing Diameter

 N/A 28.58 in

Da - Cup Frontface Backing Diameter

 N/A 34.33 in

Aa - Cage-Cone Backface Clearance

 N/A 0.42 in
a - Effective Center Location3 N/A 0.27 in

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)4 N/A 1300000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)5 N/A 1960000 lbf8740000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)6 N/A 509000 lbf2260000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 166000 lbf741000 N

Factors

K - Factor8 N/A 1.76
e - ISO Factor9 N/A 0.7
Y1 - ISO Factor10 N/A 0.97 1.44
Y2 - ISO Factor11 N/A 1.44
Cg - Geometry Factor12 N/A 0.325
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 12 Geometry constant for Lubrication Life Adjustment Factor a3l.