COMPANY HEADER
Print Back
TDI bearings have a one-piece double inner race and two single outer races and are typically supplied complete with an outer race spacer as a pre-set assembly. The bearing can be used at fixed positions on rotation shaft applications. For rotating housing application it can be used to float on the stationary shaft.
Unit of Measure

Specifications

Series

 N/A H244800

Cone Part Number

 N/A H244849D

Cup Part Number

 N/A H244810XX

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 8.6250 in

D - Cup Outer Diameter

 N/A 14.125 in

B - Double Cone Width

 N/A 7.8750 in

C - Cup Width

 N/A 3.3750 in

T - Bearing Width across Cups

 N/A 7.7499 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in
r - Cup Backface "To Clear" Radius2 N/A 0.250 in

da - Cone Frontface Backing Diameter

 N/A 9.53 in

Db - Cup Backface Backing Diameter

 N/A 12.72 in

Ab - Cage-Cone Frontface Clearance

 N/A 0.14 in

Basic Load Ratings

C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)3 N/A 84200 lbf375000 N
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4 N/A 566000 lbf2520000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)5 N/A 147000 lbf652000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 47900 lbf213000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y1 - ISO Factor9 N/A 2.03
Y2 - ISO Factor10 N/A 3.02

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1630

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 150
Cg - Geometry Factor11 N/A 0.154

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 4 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.