The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 09000

Cone Part Number

 N/A 09075

Cup Part Number

 N/A 09196

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 0.7480 in18.999 mm

D - Cup Outer Diameter

 N/A 1.9380 in49.225 mm

B - Cone Width

 N/A 0.8792 in22.332 mm

C - Cup Width

 N/A 0.6875 in17.463 mm

T - Bearing Width

 N/A 0.9375 in23.813 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 0.94 in24 mm

db - Cone Backface Backing Diameter

 N/A 0 in0 mm

Da - Cup Frontface Backing Diameter

 N/A 1.79 in44.50 mm

Db - Cup Backface Backing Diameter

 N/A 1.63 in41.40 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.1 in2.5 mm
a - Effective Center Location3 N/A -0.39 in-9.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2500 lbf11100 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 9630 lbf42800 N

C0 - Static Radial Rating

 N/A 9100 lbf40500 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1140 lbf5050 N

Factors

K - Factor7 N/A 2.2
e - ISO Factor8 N/A 0.27
Y - ISO Factor9 N/A 2.26
Cg - Geometry Factor10 N/A 0.0452
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.