COMPANY HEADER
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A 17887

Cup Part Number

 N/A 17831

Bore (d)

 N/A 1.7807 in45.23 mm

O.D. (D)

 N/A 3.149 in79.985 mm

Width (T)

 N/A 0.7812 in19.842 mm
Dynamic Radial Load Rating - 1M Revs (C1)1 N/A 15500 lbf68900 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 4020 lbf17900 N
e Factor3 N/A 0.37
K Factor4 N/A 1.6

Other Dimensions

Weight

 N/A 0.9 lb0.4 Kg

Inner Ring Width (B)

 N/A 0.8125 in20.638 mm

Outer Ring Width (C)

 N/A 0.5937 in15.08 mm
Effective Center Location5 N/A -0.15 in-3.8 mm
Max Shaft Fillet Radius6 N/A 0.08 in2.03 mm
Max Housing Fillet Radius7 N/A 0.05 in1.27 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 1.97 in50 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 2.13 in54 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 2.99 in75.9 mm

Housing Backing Shoulder Diameter - Backface (Db)

 N/A 2.83 in71.88 mm

Cage Location Relative to Backface (Aa)

 N/A 0.02 in0.5 mm

Cage Location Relative to Frontface (Ab)

 N/A 0.08 in2 mm

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)8 N/A 2510 lbf11200 N

Static Radial Load Rating (C0)

 N/A 18700 lbf83300 N

Factors

G1 Factor

 N/A 28.9

G2 Factor

 N/A 17.9
Geometry Factor (Cg)9 N/A 0.077
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 Negative value indicates effective center inside cone backface.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.