COMPANY HEADER
Print Back
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 31326M

Cone Part Number

 N/A X31326M

Cup Part Number

 N/A Y31326M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 31326XM-90KM3

Dimensions

d - Bore

 N/A 5.1181 in

D - Cup Outer Diameter

 N/A 11.0236 in

B - Cone Width

 N/A 2.5984 in

C - Cup Width

 N/A 1.7323 in

T - Bearing Width

 N/A 2.8346 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.200 in
r - Cup Backface "To Clear" Radius2 N/A 0.16 in

da - Cone Frontface Backing Diameter

 N/A 6.42 in

db - Cone Backface Backing Diameter

 N/A 7.32 in

Da - Cup Frontface Backing Diameter

 N/A 10.35 in

Db - Cup Backface Backing Diameter

 N/A 9.37 in

Ab - Cage-Cone Frontface Clearance

 N/A 0.37 in

Aa - Cage-Cone Backface Clearance

 N/A 0.62 in
a - Effective Center Location3 N/A 0.58 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 179000 N40300 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 691000 N155000 lbf

C0 - Static Radial Rating

 N/A 966000 N217000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 253000 N56900 lbf

Factors

K - Factor7 N/A 0.71
e - ISO Factor8 N/A 0.83
Y - ISO Factor9 N/A 0.73

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 411.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 42.2
Cg - Geometry Factor10 N/A 0.128
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.