3D CAD and 2D Drawings

Find and download 3D CAD and 2D drawings for key Timken products.

This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.

RELATED PRODUCTS

RELATED PRODUCTS

Unit of Measure

Specifications

Series

N/A A4000

Cone Part Number

N/A A4050

Cup Part Number

N/A A4138

Design Units

N/A Imperial

Bearing Weight

N/A 0.10 Kg0.100 lb

Cage Type

N/A Stamped Steel

Dimensions

d - Bore

N/A 12.700 mm0.5000 in

D - Cup Outer Diameter

N/A 34.989 mm1.3775 in

B - Cone Width

N/A 10.988 mm0.4326 in

C - Cup Width

N/A 8.730 mm0.3437 in

T - Bearing Width

N/A 10.998 mm0.4330 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 1.270 mm0.050 in
r - Cup Backface "To Clear" Radius2 N/A 1.27 mm0.050 in

da - Cone Frontface Backing Diameter

N/A 17.02 mm0.67 in

db - Cone Backface Backing Diameter

N/A 18.54 mm0.73 in

Da - Cup Frontface Backing Diameter

N/A 32.51 mm1.28 in

Db - Cup Backface Backing Diameter

N/A 28.96 mm1.14 in

Ab - Cage-Cone Frontface Clearance

N/A 1.8 mm0.07 in

Aa - Cage-Cone Backface Clearance

N/A 0 mm0 in
a - Effective Center Location3 N/A -2.5 mm-0.1 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 767 lbf3410 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2960 lbf13200 N

C0 - Static Radial Rating

N/A 2580 lbf11500 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 594 lbf2640 N

Factors

K - Factor7 N/A 1.29
e - ISO Factor8 N/A 0.45
Y - ISO Factor9 N/A 1.32

G1 - Heat Generation Factor (Roller-Raceway)

N/A 2.3

G2 - Heat Generation Factor (Rib-Roller End)

N/A 4.12
Cg - Geometry Factor10 N/A 0.0355
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being accessible by Timken personnel, who may be located outside your home country, as described in our Privacy Notice.