All Product Types > ENGINEERED BEARINGS > Mounted Bearings > Mounted SAF Split-Block Spherical Roller Bearings > Inch Straight Bore Mounting Pillow Block SDAF222 and SDAF223 Series > Part Number SDAF 22324  

Part Number SDAF 22324, Inch Straight Bore Mounting Pillow Block SDAF222 and SDAF223 Series

    Download PDF Download PDF   
    border="0" Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

  • Each assembly includes the housing cap and base, cap bolts, bearing, locknut and washer, stabilizing ring, and triple ring seals.
  • To order pillow block housing only, use the numbers listed in the "Housing Only" column. These units include: cap, base, cap bolts, triple ring seals and stabilizing ring.
  • Assembly and pillow blocks described on this page constitute fixed units.
  • To order float units, specify part number plus suffix "Float" or "FL".
  • If one end closed assembly is required, specify “CL” in assembly number when ordering.
  • All assemblies shown are furnished in cast iron. If cast steel is desired, add the letter "S" to the alpha prefix (e.g., SDAFS 22220).

Note: Speed ratings are found in dimension tables in the spherical roller bearing section.




Specifications  · Basic Load Ratings  · Factors

Specifications

Bearing Number
22324

Diameter S-2
5 5/16 in

Diameter S-3
4 9/16 in

A
6-5/16 in

B
21.25 in

C
7.875 in

D
2.5 in

E Max.
18.25 in

E Min.
17 in

F
4.75 in

H1
12.8125 in

Oil Level K
2.5625 in

L2
8.3750 in

Y
2.6406 in

No. of Base Bolts Required
4

Size of Base Bolts Required
1 1/8

Bolt Hole Length
1.75 in

Bolt Hole Width
1.125 in

Locknut
AN24

Lockwasher
W24

Housing Only3
SDAF324

Stabilizing Ring 1 Req'd4
SR-0-24

Triple Seal 2 Req’d at S-2
LOR127

Triple Seal 2 Req’d at S-3
LOR119

Full Timken Part Number
SDAF22324
1 Tolerance -0 to + 0.4 mm (-0 to +1/64 in)
2 Tolerance -0 to + 0.4 mm (-0 to +1/64 in)
3 "Housing Only" includes: cap, base, cap bolts, triple ring seals and stabilizing ring as required. When ordering non-standard housing only specify the shaft size.
4 Stabilizing ring is used for fixed (FX) block; do not use for float (FL) mounting.


Basic Load Ratings

C0 - Static Radial Rating
272000 lbf
1210000 N

C1(2) - Dynamic Radial Rating (Two-Rows)
244000 lbf
1080000 N


Factors

e - ISO Factor1
0.32

Y0 - ISO Factor2
2.07

Y1 - ISO Factor3
2.11

Y2 - ISO Factor4
3.15

Reference Thermal Speed Rating (Grease)
1900 rpm

Reference Thermal Speed Rating (Oil)5
2200 rpm

Cg - Geometry Factor6
0.0834
1 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
2 These factors apply for both inch and metric calculations. See engineering
3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
5 See thermal speed ratings in the engineering section.
6 Geometry constant for Lubrication Life Adjustment Factor a3l.