Aerospace / Military
Aerospace Series General Aviation Rod Ends Spherical Bearings Mil Spec Series Rod Ends Spherical Bearings Bushings Approved Part Numbers
Commercial / Industrial
Rod End Bearings Inch Rod Ends Metric Rod Ends Spherical Bearings Inch Spherical Bearings Metric Spherical Bearings
Technical Resources
Terms and Definitions Articles Technical Data FAQs Key Term Translation Custom Engineered Products
Online Catalog
Engineers power search our entire catalog of bearing and bushings, with access to every attribute and technical specification possible. View our online catalog...
CAD (0) ▾
  • Cart is empty
  1. Request CAD files
Request Information Add to CAD Cart
  • Each assembly includes the housing cap and base, cap bolts, bearing, locknut and washer, stabilizing ring and triple ring seals.
  • To order pillow block housing only, use the numbers listed in the "Housing Only" column. These units include: cap, base, cap bolts, triple ring seals, and stabilizing ring.
  • Assembly and pillow blocks described on this page constitute fixed units.
  • To order float units, specify part number plus suffix "Float" or "FL".
  • If one end closed assembly is required, specify “CL” in assembly number when ordering.
  • All assemblies shown are furnished in cast iron. If cast steel is desired, add the letter "S" to the alpha prefix (e.g., SDAFS 23152).
  • For fixed applications, both stabilizing rings must be used. Do not use stabilizing rings for “Float” mounting.
Unit of Measure

Specifications

Bearing Number

 N/A 23188

Diameter S-2

 N/A 19 1/2 in

Diameter S-3

 N/A 17.0000 in

A

 N/A 17 in

B

 N/A 52 in

C

 N/A 21 in

D

 N/A 5.5 in

E Max.

 N/A 46.125 in

E Min.

 N/A 44.375 in

F

 N/A 14.5 in
H1 N/A 33.75 in

Oil Level K

 N/A 5.5625 in
L2 N/A 22.25 in

No. of Base Bolts Required

 N/A 4

Size of Base Bolts Required

 N/A 2 1/4

Bolt Hole Length

 N/A 3.125 in

Bolt Hole Width

 N/A 2.25 in

Locknut

 N/A NO88

Lockplate

 N/A P88
Housing Only3 N/A SDAF3188
Stabilizing Ring 1 Req'd4 N/A A8976

Triple Seal 2 Req’d at S-2

 N/A ER926-1

Triple Seal 2 Req’d at S-3

 N/A ER838-1

Full Timken Part Number

 N/A SDAF23188

Basic Load Ratings

C0 - Static Radial Rating

 N/A 2310000 lbf10300000 N

C1(2) - Dynamic Radial Rating (Two-Rows)

 N/A 1340000 lbf5970000 N

Factors

e - ISO Factor5 N/A 0.3
Y0 - ISO Factor6 N/A 2.21
Y1 - ISO Factor7 N/A 2.26
Y2 - ISO Factor8 N/A 3.37

Reference Thermal Speed Rating (Grease)

 N/A 410 rpm
Reference Thermal Speed Rating (Oil)9 N/A 450 rpm
Cg - Geometry Factor10 N/A 0.0984
  • 1 Tolerance -0 to + 0.4 mm (-0 to +1/64 in)
  • 2 Tolerance -0 to + 0.4 mm (-0 to +1/64 in)
  • 3 "Housing Only" includes: cap, base, cap bolts, triple ring seals and stabilizing ring as required. When ordering non-standard housing only specify the shaft size.
  • 4 Stabilizing ring is used for fixed (FX) block; do not use for float (FL) mounting.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These factors apply for both inch and metric calculations. See engineering
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 See thermal speed ratings in the engineering section.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.