Aerospace / Military
Aerospace Series General Aviation Rod Ends Spherical Bearings Mil Spec Series Rod Ends Spherical Bearings Bushings Approved Part Numbers
Commercial / Industrial
Rod End Bearings Inch Rod Ends Metric Rod Ends Spherical Bearings Inch Spherical Bearings Metric Spherical Bearings
Technical Resources
Terms and Definitions Articles Technical Data FAQs Key Term Translation Custom Engineered Products
Online Catalog
Engineers power search our entire catalog of bearing and bushings, with access to every attribute and technical specification possible. View our online catalog...
CAD (0) ▾
  • Cart is empty
  1. Request CAD files
Request Information Add to CAD Cart
  • Each assembly includes the housing cap and base, cap bolts, bearing, bearing adapter, locknut and lockwasher, stabilizing ring and triple ring seals.
  • To order pillow block housing only, use the numbers listed in the "Housing Only" column. These units include: cap, base, cap bolts, triple ring seals and stabilizing ring.
  • Assembly and pillow blocks described on this page constitute fixed units.
  • To order float units, specify part number plus suffix "Float" or "FL".
  • If one end closed assembly is required, specify “CL” in assembly number when ordering.
  • All assemblies shown are furnished in cast iron. If cast steel is desired, add the letter “S” to the alpha prefix (e.g., SDAFS 23152K).

When ordering non-standard pillow block assemblies specify the shaft size.
Unit of Measure

Specifications

Bearing Number

 N/A 23176K

Diameter S-1

 N/A 14 in

A

 N/A 14.5 in

B

 N/A 46 in

C

 N/A 17.125 in

D

 N/A 5.25 in

E Max.

 N/A 40.75 in

E Min.

 N/A 39.25 in

F

 N/A 11 in

H

 N/A 28.875 in

L

 N/A 17.75 in

Bolt Hole Length

 N/A 2.75 in

Bolt Hole Width

 N/A 2 in
Adapter Assembly Number1 N/A SNP-3176 x 14
Housing Only2 N/A SDAF3176K x 14
Stabilizing Ring 1 Req'd3 N/A A8978

Triple Seal Req'd

 N/A ER 876-1

Full Timken Part Number

 N/A SDAF23176K14

Basic Load Ratings

C0 - Static Radial Rating

 N/A 1700000 lbf7580000 N

C1(2) - Dynamic Radial Rating (Two-Rows)

 N/A 1010000 lbf4490000 N

Factors

e - ISO Factor4 N/A 0.3
Y0 - ISO Factor5 N/A 2.23
Y1 - ISO Factor6 N/A 2.28
Y2 - ISO Factor7 N/A 3.39

Reference Thermal Speed Rating (Grease)

 N/A 510 rpm
Reference Thermal Speed Rating (Oil)8 N/A 560 rpm
Cg - Geometry Factor9 N/A 0.0895
  • 1 Includes sleeve, locknut and lockwasher. Add shaft size to order.
  • 2 "Housing Only" includes: cap, base, cap bolts, triple ring seals and stabilizing ring as required. When ordering non-standard housing only specify the shaft size.
  • 3 Stabilizing ring is used for fixed (FX) block; do not use for float (FL) mounting.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. See engineering
  • 6 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 See thermal speed ratings in the engineering section.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.