Batch CAD Cart (0)
  • Cart is empty
  • Each assembly includes the housing cap and base, cap bolts, bearing, bearing adapter, locknut and lockwasher, stabilizing ring and triple ring seals.
  • To order pillow block housing only, use the numbers listed in the "Housing Only" column. These units include: cap, base, cap bolts, triple ring seals and stabilizing ring.
  • Assembly and pillow blocks described on this page constitute fixed units.
  • To order float units, specify part number plus suffix "Float" or "FL".
  • If one end closed assembly is required, specify “CL” in assembly number when ordering.
  • All assemblies shown are furnished in cast iron. If cast steel is desired, add the letter “S” to the alpha prefix (e.g., SDAFS 23152K).

When ordering non-standard pillow block assemblies specify the shaft size.
Unit of Measure

Specifications

Bearing Number

N/A 23260K

Diameter S-1

N/A 10 15/16 in

A

N/A 12.8125 in

B

N/A 41.75 in

C

N/A 15.75 in

D

N/A 4.5 in

E Max.

N/A 36.5 in

E Min.

N/A 35 in

F

N/A 10.5 in

H

N/A 25.75 in

L

N/A 16.25 in

Bolt Hole Length

N/A 2.625 in

Bolt Hole Width

N/A 1.875 in
Adapter Assembly Number1 N/A SNP-3260 x 10-15/16
Housing Only2 N/A SDAF3260K x 10-15/16
Stabilizing Ring 1 Req'd3 N/A A8970

Triple Seal Req'd

N/A ER 974

Full Timken Part Number

N/A SDAF23260K10-15/16

Basic Load Ratings

C0 - Static Radial Rating

N/A 1390000 lbf6170000 N

C1(2) - Dynamic Radial Rating (Two-Rows)

N/A 946000 lbf4210000 N

Factors

e - ISO Factor4 N/A 0.34
Y0 - ISO Factor5 N/A 1.96
Y1 - ISO Factor6 N/A 2
Y2 - ISO Factor7 N/A 2.98

Reference Thermal Speed Rating (Grease)

N/A 530 rpm
Reference Thermal Speed Rating (Oil)8 N/A 580 rpm
Cg - Geometry Factor9 N/A 0.1297
  • 1 Includes sleeve, locknut and lockwasher. Add shaft size to order.
  • 2 "Housing Only" includes: cap, base, cap bolts, triple ring seals and stabilizing ring as required. When ordering non-standard housing only specify the shaft size.
  • 3 Stabilizing ring is used for fixed (FX) block; do not use for float (FL) mounting.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. See engineering
  • 6 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 See thermal speed ratings in the engineering section.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.