Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A 295000

Cone Part Number

N/A EE295950

Design Units

N/A Imperial

Cage Type

N/A Pin-Type
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 948000 lbf4220000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 246000 lbf1090000 N

Dimensions

d - Cone Bore

N/A 9.5000 in241.300 mm

B - Cone Width

N/A 4.7500 in120.650 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 0.25 in6.4 mm

da - Cone Frontface Backing Diameter

N/A 10.87 in276 mm

db - Cone Backface Backing Diameter

N/A 11.22 in285 mm

Ab - Cage-Cone Frontface Clearance

N/A 0.2 in5.1 mm

Aa - Cage-Cone Backface Clearance

N/A 0.69 in17.5 mm
a - Effective Center Location4 N/A -1.22 in-31 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 141000 lbf628000 N
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 544000 lbf2420000 N

C0 - Static Radial Rating

N/A 744000 lbf3310000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 75600 lbf336000 N

Factors

K - Factor8 N/A 1.87

G1 - Heat Generation Factor (Roller-Raceway)

N/A 2250

G2 - Heat Generation Factor (Rib-Roller End)

N/A 172
Cg - Geometry Factor9 N/A 0.166
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.