Request Information
UFH Type - Flange-to-Shaft
    A flange-to-shaft configuration, this couples flange mounted equipment to a shaft with all the benefits of Uniflex versatility. The stock flange plate is the same as used on the UF Type.

    The one-piece UFH Type coupling is similar to the U Type, except that one hub is replaced by a flange plate. Stock flange sizes are shown in the Dimensional Data table below but other sizes can be made to order. As with the other Uniflex styles, this coupling compensates for high degrees of angular and parallel misalignment with very little backlash or windup and is reliable in harsh or severe environments.

    Regular and short versions are available for each size to accommodate different overall length requirements. For increased versatility, the hub can be modified with a tapered, spline, hex or square bore. The standard hub is furnished with either a pre-drilled pin hole or with a keyway and set screw. Specify when ordering.
    Note: The UFH Type coupling does not come with assembly hardware. Assembly hardware must be purchased separately.
Unit of Measure

Specifications

Description 

 N/A UFH150R-CP-1-3/8-5/16X5/32KW

Hub Style

 N/A Regular

Type

 N/A Flange-to-Shaft

Material

 N/A Steel

Weight

 N/A 10.00 lb

Color

 N/A Gray/Metallic

Bore Type

 N/A Finished Bore

# of Mounting Screws Required

 N/A 4

Dimensional Data

Bore Size 

 N/A 1 3/8 in

Hub Size

 N/A UFH150R

Set Screw Thread Size (Dimension T)

 N/A 3/8-16

Keyway Size (W x D)

 N/A 5/16 x 5/32 in

Dimension HD

 N/A 2.980 in75.69 mm

Overall Length

 N/A 4.860 in123.44 mm

Pin Location (Dimension SL)

 N/A 0.810 in

Length thru Bore

 N/A 1.880 in47.75 mm

Min. Bore (Dimensions ID1/ID2)

 N/A 0.750 in19.05 mm

Max. Bore (Dimensions ID1/ID2)

 N/A 1.5 in38 mm

Dimension BC

 N/A 4.380 in111.25 mm

Dimension D

 N/A 5.000 in127.00 mm

Flange Diameter (Dimension FD)

 N/A 5.380 in136.65 mm

Dimension FL

 N/A 0.630 in16.00 mm

Mounting Screw Thread Size

 N/A 3/8-16

Cubic inches

 N/A 140.66978 in³

Performance Data

Operating Temperature Range

 N/A -40 to 250 ºF

Max. Torque

 N/A 1890 in·lb

Max. Speed

 N/A 3000 rpm

Max. Recommended End Play

 N/A 0.040 in1.02 mm

Max. Parallel Offset

 N/A 0.041 in1.04 mm

Wind-Up Angle at Nominal Torque

 N/A 0.85 º

Wind-Up Angle at Max. Torque

 N/A 3.00 º

Rated HP at 100 rpm

 N/A 3.02 hp

# of Set Screws Required

 N/A 1

Coupling Design

Coupling Design

 N/A Flexible Spring Type Coupling with Exclusive Triple Wound Spring Design
    The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.

Notes

Notes 

 N/A
  • Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.
  • OAL & Dimension FL Tolerance + .12 inch.
  • Mounting screws not supplied.