Menu
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information
UFH Type - Flange-to-Shaft
    A flange-to-shaft configuration, this couples flange mounted equipment to a shaft with all the benefits of Uniflex versatility. The stock flange plate is the same as used on the UF Type.

    The one-piece UFH Type coupling is similar to the U Type, except that one hub is replaced by a flange plate. Stock flange sizes are shown in the Dimensional Data table below but other sizes can be made to order. As with the other Uniflex styles, this coupling compensates for high degrees of angular and parallel misalignment with very little backlash or windup and is reliable in harsh or severe environments.

    Regular and short versions are available for each size to accommodate different overall length requirements. For increased versatility, the hub can be modified with a tapered, spline, hex or square bore. The standard hub is furnished with either a pre-drilled pin hole or with a keyway and set screw. Specify when ordering.
    Note: The UFH Type coupling does not come with assembly hardware. Assembly hardware must be purchased separately.
Unit of Measure

Specifications

Description 

 N/A UFH75S-CP-3/4-3/16X3/32KW

Hub Style

 N/A Short

Type

 N/A Flange-to-Shaft

Material

 N/A Steel

Weight

 N/A 0.87 lb

Color

 N/A Gray/Metallic

Bore Type

 N/A Finished Bore

# of Mounting Screws Required

 N/A 3

Dimensional Data

Bore Size 

 N/A 3/4 in

Hub Size

 N/A UFH75S

Set Screw Thread Size (Dimension T)

 N/A 1/4-20

Keyway Size (W x D)

 N/A 3/16 x 3/32 in

Dimension HD

 N/A 1.420 in36.07 mm

Overall Length

 N/A 2.000 in50.80 mm

Pin Location (Dimension SL)

 N/A 0.41 in

Length thru Bore

 N/A 0.840 in21.34 mm

Min. Bore (Dimensions ID1/ID2)

 N/A 0.375 in9.53 mm

Max. Bore (Dimensions ID1/ID2)

 N/A 0.750 in19.00 mm

Dimension BC

 N/A 2.000 in50.80 mm

Dimension D

 N/A 2.880 in73.15 mm

Flange Diameter (Dimension FD)

 N/A 2.500 in63.50 mm

Dimension FL

 N/A 0.380 in9.65 mm

Mounting Screw Thread Size

 N/A 1/4-20

Cubic inches

 N/A 12.50000 in³

Performance Data

Operating Temperature Range

 N/A -40 to 250 ºF

Max. Torque

 N/A 175 in·lb

Max. Speed

 N/A 20000.00 rpm

Max. Recommended End Play

 N/A 0.020 in0.51 mm

Max. Parallel Offset

 N/A 0.019 in0.48 mm

Wind-Up Angle at Nominal Torque

 N/A 1.12 º

Wind-Up Angle at Max. Torque

 N/A 3.00 º

Rated HP at 100 rpm

 N/A 0.28 hp

# of Set Screws Required

 N/A 1

Coupling Design

Coupling Design

 N/A Flexible Spring Type Coupling with Exclusive Triple Wound Spring Design
    The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.

Notes

Notes 

 N/A
  • Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.
  • OAL & Dimension FL Tolerance + .12 inch.
  • Mounting screws not supplied.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.