Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32260

Cone Part Number

 N/A X32260M

Design Units

 N/A METRIC

Cage Type

 N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 5390000 N1210000 lbf
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 1400000 N314000 lbf

Full Timken Part Number

 N/A 32260

Dimensions

d - Cone Bore

 N/A 300 mm11.811 in

B - Cone Width

 N/A 140 mm5.5118 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 6 mm0.236 in

da - Cone Frontface Backing Diameter

 N/A 345 mm13.58 in

db - Cone Backface Backing Diameter

 N/A 359 mm14.13 in

Ab - Cage-Cone Frontface Clearance

 N/A 8.9 mm0.35 in

Aa - Cage-Cone Backface Clearance

 N/A 15.8 mm0.62 in
a - Effective Center Location4 N/A -17.8 mm-0.7 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 802000 N180000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 3090000 N695000 lbf

C0 - Static Radial Rating

 N/A 5310000 N1190000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 597000 N134000 lbf

Factors

K - Factor8 N/A 1.34

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3303.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 165.8
Cg - Geometry Factor9 N/A 0.212
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.