Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A H919900

Cone Part Number

 N/A H919942

Cup Part Number

 N/A H919911

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3.3125 in84.138 mm

D - Cup Outer Diameter

 N/A 7-5/8 in193.675 mm

B - Cone Width

 N/A 1.9291 in48.999 mm

C - Cup Width

 N/A 1.3582 in34.498 mm

T - Bearing Width

 N/A 2.0472 in51.999 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 4.32 in109.7 mm

db - Cone Backface Backing Diameter

 N/A 4.84 in123 mm

Da - Cup Frontface Backing Diameter

 N/A 7.09 in180.09 mm

Db - Cup Backface Backing Diameter

 N/A 6.3 in160.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.23 in5.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.28 in7.1 mm
a - Effective Center Location3 N/A 0.32 in8.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 21700 lbf96700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 83800 lbf373000 N

C0 - Static Radial Rating

 N/A 103000 lbf458000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 29600 lbf132000 N

Factors

K - Factor7 N/A 0.73
e - ISO Factor8 N/A 0.79
Y - ISO Factor9 N/A 0.75

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 163.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 23.2
Cg - Geometry Factor10 N/A 0.119
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.