2TS-DM assemblies are comprised of two single-row bearings with abutting back facing inner rings and an outer ring spacer with lubricating holes is typical. These are generally used at fixed positions on rotating shaft applications.

Design Attributes:
  • Two single row bearings, with or without a spacer
  • When spacers are used, bearing is furnished as a preset, matched assembly
  • Spacers available with or without lubricant grooves and holes
    • Request Information
    Unit of Measure

    Other Dimensions

    Weight

    		 N/A 4.37 Kg9.65 lb

    Width (T)

    		 N/A 2.875 in73.025 mm

    B - Width

    		 N/A 2.625 in66.676 mm
    Max Shaft Fillet Radius1 N/A 0.03 in0.800 mm
    Max Housing Fillet Radius2 N/A 0.130 in3.30 mm

    Shaft Backing Shoulder Diameter - Backface (db)

    		 N/A 3.66 in93 mm

    Housing Backing Shoulder Diameter - Frontface (Da)

    		 N/A 4.88 in123.95 mm

    Key Dimensions

    Cone Part Number

    		 N/A HM911245

    Cup Part Number

    		 N/A HM911210

    Related Assembly Number(s)

    		 N/A HM911245-90030

    Outer Spacer Part Number

    		 N/A HM911210EC

    Design Unit

    		 N/A Inch

    Bore (d)

    		 N/A 2.3750 in60.325 mm

    O.D. (D)

    		 N/A 5.1250 in130.175 mm
    Dynamic Radial Load Rating - 90M Revs (C90) 3 N/A 11500 lbf51200 N
    Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row)4 N/A 20100 lbf89200 N
    K Factor 5 N/A 0.71
    e Factor 6 N/A 0.82

    Ratings

    C1 - Dynamic Radial Rating (1 million revolutions)7 N/A 77400 lbf344000 N
    Ca90 - Dynamic Thrust Rating (90 million revolutions)8 N/A 16200 lbf71900 N

    Factors

    Y1 Factor 9 N/A 0.82
    Y2 Factor 10 N/A 1.23
    • 1 These maximum fillet radii will be cleared by the bearing corners.
    • 2 These maximum fillet radii will be cleared by the bearing corners.
    • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
    • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
    • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
    • 6 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
    • 7 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
    • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
    • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
    • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.