3D CAD and 2D Drawings

Find and download 3D CAD and 2D drawings for key Timken products.

Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.

RELATED PRODUCTS

RELATED PRODUCTS

Unit of Measure

Specifications

Series

N/A 3600

Cone Part Number

N/A 3659

Cup Part Number

N/A 3620

Design Units

N/A Imperial

Bearing Weight

N/A 0.4 Kg1 lb

Cage Type

N/A Stamped Steel

Dimensions

d - Bore

N/A 23.813 mm0.9375 in

D - Cup Outer Diameter

N/A 61.913 mm2.4375 in

B - Cone Width

N/A 30.417 mm1.1975 in

C - Cup Width

N/A 23.813 mm0.9375 in

T - Bearing Width

N/A 28.575 mm1.1250 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 2.290 mm0.09 in
r - Cup Backface "To Clear" Radius2 N/A 3.3 mm0.130 in

da - Cone Frontface Backing Diameter

N/A 31.5 mm1.24 in

db - Cone Backface Backing Diameter

N/A 35.56 mm1.4 in

Da - Cup Frontface Backing Diameter

N/A 57.90 mm2.28 in

Db - Cup Backface Backing Diameter

N/A 52.07 mm2.05 in

Ab - Cage-Cone Frontface Clearance

N/A 1 mm0.04 in

Aa - Cage-Cone Backface Clearance

N/A 1.3 mm0.05 in
a - Effective Center Location3 N/A -11.9 mm-0.47 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 5160 lbf23000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 19900 lbf88600 N

C0 - Static Radial Rating

N/A 20200 lbf89800 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 2500 lbf11100 N

Factors

K - Factor7 N/A 2.07
e - ISO Factor8 N/A 0.28
Y - ISO Factor9 N/A 2.13

G1 - Heat Generation Factor (Roller-Raceway)

N/A 17

G2 - Heat Generation Factor (Rib-Roller End)

N/A 6.38
Cg - Geometry Factor10 N/A 0.0592
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being accessible by Timken personnel, who may be located outside your home country, as described in our Privacy Notice.