3D CAD and 2D Drawings

Find and download 3D CAD and 2D drawings for key Timken products.

This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.

RELATED PRODUCTS

RELATED PRODUCTS

Unit of Measure

Specifications

Series

N/A A2000

Cone Part Number

N/A A2031

Cup Part Number

N/A A2126

Design Units

N/A Imperial

Bearing Weight

N/A 0.000 Kg0.100 lb

Cage Type

N/A Stamped Steel

Dimensions

d - Bore

N/A 7.938 mm0.3125 in

D - Cup Outer Diameter

N/A 31.991 mm1.2595 in

B - Cone Width

N/A 10.785 mm0.4246 in

C - Cup Width

N/A 7.938 mm0.3125 in

T - Bearing Width

N/A 10.008 mm0.3940 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.510 mm0.02 in
r - Cup Backface "To Clear" Radius2 N/A 1.27 mm0.050 in

da - Cone Frontface Backing Diameter

N/A 12.45 mm0.49 in

db - Cone Backface Backing Diameter

N/A 12.95 mm0.51 in

Da - Cup Frontface Backing Diameter

N/A 30.00 mm1.18 in

Db - Cup Backface Backing Diameter

N/A 25.91 mm1.02 in

Ab - Cage-Cone Frontface Clearance

N/A 2.3 mm0.09 in

Aa - Cage-Cone Backface Clearance

N/A -0.8 mm-0.03 in
a - Effective Center Location3 N/A -3 mm-0.12 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 630 lbf2800 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2430 lbf10800 N

C0 - Static Radial Rating

N/A 2070 lbf9230 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 437 lbf1940 N

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.41
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

N/A 1.7

G2 - Heat Generation Factor (Rib-Roller End)

N/A 3.17
Cg - Geometry Factor10 N/A 0.0308
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being accessible by Timken personnel, who may be located outside your home country, as described in our Privacy Notice.