Aerospace / Military
Aerospace Series General Aviation Rod Ends Spherical Bearings Mil Spec Series Rod Ends Spherical Bearings Bushings Approved Part Numbers
Commercial / Industrial
Rod End Bearings Inch Rod Ends Metric Rod Ends Spherical Bearings Inch Spherical Bearings Metric Spherical Bearings
Technical Resources
Terms and Definitions Articles Technical Data FAQs Key Term Translation Custom Engineered Products
Online Catalog
Engineers power search our entire catalog of bearing and bushings, with access to every attribute and technical specification possible. View our online catalog...
Request Information
Often referred to as snap-ring assemblies, type 2S consist of two basic single-row bearings (type TS). They are supplied complete with inner-ring and outer-ring spacers to give a pre determined bearing setting when assembled. Type 2S have a specified setting range to suit the duty of the application. They have an inner-ring spacer and a snap-ring, which also serves as the outer-ring spacer, to give axial location in a through-bored housing.
Unit of Measure

Key Dimensions

Cone Part Number

 N/A A4059

Cup Part Number

 N/A A4138

Inner Spacer Part Number

 N/A X5SA4059

Outer Spacer Part Number

 N/A K524667R

Bore (d)

 N/A 0.5901 in14.989 mm

O.D. (D)

 N/A 1.3775 in34.989 mm

Width (T)

 N/A 0.9660 in24.536 mm
Dynamic Radial Load Rating - 1M Revs (C1)1 N/A 5150 lbf22900 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 767 lbf3410 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row)3 N/A 1330 lbf5940 N
e Factor 4 N/A 0.45
K Factor 5 N/A 1.29

Other Dimensions

Weight

 N/A 0.10 Kg0.24 lb

Width (C)

 N/A 0.7874 in20.000 mm

Snap Ring Diameter

 N/A 1.43 in36.35 mm

Snap Ring Width

 N/A 0.10 in2.54 mm
Max Shaft Fillet Radius6 N/A 0.030 in0.8 mm

Shaft Backing Shoulder Dia. - Backface (db)

 N/A 0.77 in19.5 mm

Housing Backing Shoulder Dia. - Frontface (Da)

 N/A 1.28 in32.51 mm

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)7 N/A 594 lbf2640 N

Factors

Y1 Factor 8 N/A 1.49
Y2 Factor 9 N/A 2.22
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.