Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L580900

Cone Part Number

 N/A JL580946

Design Units

 N/A METRIC

Cage Type

 N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 5030000 N1130000 lbf
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 1300000 N293000 lbf

Full Timken Part Number

 N/A L580900

Dimensions

d - Cone Bore

 N/A 630.000 mm24.8031 in

B - Cone Width

 N/A 100 mm3.937 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 7.620 mm0.300 in

da - Cone Frontface Backing Diameter

 N/A 660 mm25.98 in

db - Cone Backface Backing Diameter

 N/A 672 mm26.46 in

Ab - Cage-Cone Frontface Clearance

 N/A 14 mm0.55 in

Aa - Cage-Cone Backface Clearance

 N/A 14 mm0.55 in
a - Effective Center Location4 N/A 35.6 mm1.4 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 748000 N168000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 2890000 N649000 lbf

C0 - Static Radial Rating

 N/A 5910000 N1330000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 510000 N115000 lbf

Factors

K - Factor8 N/A 1.47

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 9816.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 894.2
Cg - Geometry Factor9 N/A 0.29
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.