3D CAD and 2D Drawings

Find and download 3D CAD and 2D drawings for key Timken products.

Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A LM67000

Cone Part Number

N/A JLM67042

Design Units

N/A METRIC

Cage Type

N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 18300 lbf81300 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 4740 lbf21100 N

Dimensions

d - Bore

N/A 27.000 mm1.0630 in

B - Cone Width

N/A 16.764 mm0.6600 in

WPD

N/A 54.1 mm2.13 in

DD

N/A 48.4 mm1.91 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 0.510 mm0.02 in

da - Cone Frontface Backing Diameter

N/A 33 mm1.3 in

db - Cone Backface Backing Diameter

N/A 33.5 mm1.32 in

Ab - Cage-Cone Frontface Clearance

N/A 1.3 mm0.05 in

Aa - Cage-Cone Backface Clearance

N/A 0.3 mm0.01 in
a - Effective Center Location4 N/A -3 mm-0.12 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 12100 N2720 lbf
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 46700 N10500 lbf

C0 - Static Radial Rating

N/A 44600 N10000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 8550 N1920 lbf

Factors

K - Factor8 N/A 1.42

G1 - Heat Generation Factor (Roller-Raceway)

N/A 12.8

G2 - Heat Generation Factor (Rib-Roller End)

N/A 9.7
Cg - Geometry Factor9 N/A 0.0612
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being accessible by Timken personnel, who may be located outside your home country, as described in our Privacy Notice.