3D CAD and 2D Drawings

Find and download 3D CAD and 2D drawings for key Timken products.

Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A 30204M

Cone Part Number

N/A X30204M

Design Units

N/A METRIC

Cage Type

N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 13000 lbf57900 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 3370 lbf15000 N

Dimensions

d - Bore

N/A 20.000 mm0.7874 in

B - Cone Width

N/A 14.000 mm0.5512 in

WPD

N/A 42.5 mm1.67 in

DD

N/A 38.1 mm1.5 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 1.020 mm0.04 in

da - Cone Frontface Backing Diameter

N/A 26 mm1.02 in

db - Cone Backface Backing Diameter

N/A 27.5 mm1.08 in

Ab - Cage-Cone Frontface Clearance

N/A 2.8 mm0.11 in

Aa - Cage-Cone Backface Clearance

N/A -0.5 mm-0.02 in
a - Effective Center Location4 N/A -4.3 mm-0.17 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 8620 N1940 lbf
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 33200 N7470 lbf

C0 - Static Radial Rating

N/A 33000 N7420 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 5090 N1140 lbf

Factors

K - Factor8 N/A 1.69

G1 - Heat Generation Factor (Roller-Raceway)

N/A 7.1

G2 - Heat Generation Factor (Rib-Roller End)

N/A 7.3
Cg - Geometry Factor9 N/A 0.0474
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being accessible by Timken personnel, who may be located outside your home country, as described in our Privacy Notice.