Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 30313

Cone Part Number

 N/A X30313

Design Units

 N/A METRIC

Cage Type

 N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 387000 N87000 lbf
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 100000 N22600 lbf

Full Timken Part Number

 N/A 30313

Dimensions

d - Cone Bore

 N/A 65 mm2.5591 in

B - Cone Width

 N/A 33.000 mm1.2992 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 3.050 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 75 mm2.95 in

db - Cone Backface Backing Diameter

 N/A 80 mm3.15 in

Ab - Cage-Cone Frontface Clearance

 N/A 5.6 mm0.22 in

Aa - Cage-Cone Backface Clearance

 N/A 1.8 mm0.07 in
a - Effective Center Location4 N/A -7.6 mm-0.3 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 57600 N13000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 222000 N50000 lbf

C0 - Static Radial Rating

 N/A 242000 N54400 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 34000 N7650 lbf

Factors

K - Factor8 N/A 1.69

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 87.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 22.9
Cg - Geometry Factor9 N/A 0.0743
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.