Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A 32305

Cone Part Number

N/A X32305

Design Units

N/A METRIC

Cage Type

N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 126000 N28300 lbf
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 32700 N7350 lbf

Full Timken Part Number

N/A 32305

Dimensions

d - Cone Bore

N/A 25 mm0.9843 in

B - Cone Width

N/A 24.000 mm0.9449 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 1.520 mm0.06 in

da - Cone Frontface Backing Diameter

N/A 31.5 mm1.24 in

db - Cone Backface Backing Diameter

N/A 35 mm1.38 in

Ab - Cage-Cone Frontface Clearance

N/A 3 mm0.12 in

Aa - Cage-Cone Backface Clearance

N/A 1.5 mm0.06 in
a - Effective Center Location4 N/A -9.7 mm-0.38 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 18800 N4220 lbf
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 72400 N16300 lbf

C0 - Static Radial Rating

N/A 72400 N16300 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 9640 N2170 lbf

Factors

K - Factor8 N/A 1.95

G1 - Heat Generation Factor (Roller-Raceway)

N/A 15.1

G2 - Heat Generation Factor (Rib-Roller End)

N/A 7.2
Cg - Geometry Factor9 N/A 0.058
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.