All Product Types > ENGINEERED BEARINGS > Tapered Roller Bearings > Tapered Roller Bearings - Single Cones > Tapered Roller Bearings - Single Cones - Imperial > Part Number HM803149  

Part Number HM803149, Tapered Roller Bearings - Single Cones - Imperial

    Download PDF Download PDF   
    border="0" Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.




Specifications  · Dimensions  · Abutment and Fillet Dimensions  · Basic Load Ratings  · Factors

Specifications

Cone Part Number
HM803149

Design Units
Imperial

Cage Type
Stamped Steel

C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1
44500 lbf
198000 N

C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2
11500 lbf
51300 N
1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.


Dimensions

d - Cone Bore
1 3/4 in
44.450 mm

B - Cone Width
1.1563 in
29.370 mm


Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1
0.14 in
3.560 mm

da - Cone Frontface Backing Diameter
2.1 in
53.4 mm

db - Cone Backface Backing Diameter
2.44 in
62 mm

Ab - Cage-Cone Frontface Clearance
0.11 in
2.8 mm

Aa - Cage-Cone Backface Clearance
0.04 in
1 mm

a - Effective Center Location2
-0.17 in
-4.3 mm
1 These maximum fillet radii will be cleared by the bearing corners.
2 Negative value indicates effective center inside cone backface.


Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)1
6630 lbf
29500 N

C1 - Dynamic Radial Rating (1 million revolutions)2
25600 lbf
114000 N

C0 - Static Radial Rating
32400 lbf
144000 N

Ca90 - Dynamic Thrust Rating (90 million revolutions)3
6200 lbf
27600 N
1 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
2 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.


Factors

K - Factor1
1.07

G1 - Heat Generation Factor (Roller-Raceway)
39.2

G2 - Heat Generation Factor (Rib-Roller End)
10.6

Cg - Geometry Factor2
0.0974
1 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
2 Geometry constant for Lubrication Life Adjustment Factor a3l.



 DOWNLOADS 

Tapered Roller Bearing Engineering Information
(PDF, 663KB)

Bearing Life Calculation Tool

Bearing Dimensional Tolerances