All Product Types > ENGINEERED BEARINGS > Tapered Roller Bearings > Tapered Roller Bearings - Single Cones > Tapered Roller Bearings - Single Cones - Imperial > Part Number LL639249  

Part Number LL639249, Tapered Roller Bearings - Single Cones - Imperial

    Download PDF Download PDF   
    border="0" Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.




Specifications  · Dimensions  · Abutment and Fillet Dimensions  · Basic Load Ratings  · Factors

Specifications

Cone Part Number
LL639249

Design Units
Imperial

Cage Type
Stamped Steel

C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1
67500 lbf
300000 N

C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2
17500 lbf
77800 N
1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.


Dimensions

d - Cone Bore
7.7500 in
196.850 mm

B - Cone Width
0.9062 in
23.017 mm


Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1
0.06 in
1.520 mm

da - Cone Frontface Backing Diameter
7.99 in
203 mm

db - Cone Backface Backing Diameter
8.07 in
205 mm

Ab - Cage-Cone Frontface Clearance
0.14 in
3.6 mm

Aa - Cage-Cone Backface Clearance
0.04 in
1 mm

a - Effective Center Location2
0.69 in
17.5 mm
1 These maximum fillet radii will be cleared by the bearing corners.
2 Negative value indicates effective center inside cone backface.


Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)1
10100 lbf
44700 N

C1 - Dynamic Radial Rating (1 million revolutions)2
38800 lbf
172000 N

C0 - Static Radial Rating
76300 lbf
340000 N

Ca90 - Dynamic Thrust Rating (90 million revolutions)3
7190 lbf
32000 N
1 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
2 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.


Factors

K - Factor1
1.4

G1 - Heat Generation Factor (Roller-Raceway)
443

G2 - Heat Generation Factor (Rib-Roller End)
230.2

Cg - Geometry Factor2
0.133
1 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
2 Geometry constant for Lubrication Life Adjustment Factor a3l.



 DOWNLOADS 

Tapered Roller Bearing Engineering Information
(PDF, 663KB)

Bearing Life Calculation Tool

Bearing Dimensional Tolerances