Aerospace / Military
Aerospace Series General Aviation Rod Ends Spherical Bearings Mil Spec Series Rod Ends Spherical Bearings Bushings Approved Part Numbers
Commercial / Industrial
Rod End Bearings Inch Rod Ends Metric Rod Ends Spherical Bearings Inch Spherical Bearings Metric Spherical Bearings
Technical Resources
Terms and Definitions Articles Technical Data FAQs Key Term Translation Custom Engineered Products
Online Catalog
Engineers power search our entire catalog of bearing and bushings, with access to every attribute and technical specification possible. View our online catalog...
CAD (0) ▾
  • Cart is empty
  1. Request CAD files
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL687900

Cone Part Number

 N/A LL687949

Design Units

 N/A Imperial

Cage Type

 N/A Pin-Type
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 654000 lbf2910000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 169000 lbf754000 N

Dimensions

d - Cone Bore

 N/A 38.5000 in977.900 mm

B - Cone Width

 N/A 2.5 in63.5 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 0.25 in6.4 mm

da - Cone Frontface Backing Diameter

 N/A 39.57 in1005 mm

db - Cone Backface Backing Diameter

 N/A 39.76 in1010 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.46 in11.68 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.15 in3.81 mm
a - Effective Center Location4 N/A 4.52 in114.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 97300 lbf433000 N
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 375000 lbf1670000 N

C0 - Static Radial Rating

 N/A 1190000 lbf5290000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 72700 lbf323000 N

Factors

K - Factor8 N/A 1.34

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 18900

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 3190.6
Cg - Geometry Factor9 N/A 0.363
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.