Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM283600

Cone Part Number

 N/A LM283649H

Design Units

 N/A Imperial

Cage Type

 N/A Stamped Steel
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 2010000 lbf8930000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 521000 lbf2320000 N

Dimensions

d - Cone Bore

 N/A 29.5000 in749.3 mm

B - Cone Width

 N/A 6.3125 in160.338 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 0.25 in6.4 mm

da - Cone Frontface Backing Diameter

 N/A 30.94 in786 mm

db - Cone Backface Backing Diameter

 N/A 31.18 in792 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.27 in6.9 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.65 in16.5 mm
a - Effective Center Location4 N/A 0.24 in6.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 299000 lbf1330000 N
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 1150000 lbf5130000 N

C0 - Static Radial Rating

 N/A 2980000 lbf13200000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 170000 lbf757000 N

Factors

K - Factor8 N/A 1.76

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 20571.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1126.8
Cg - Geometry Factor9 N/A 0.351
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.