Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM769300

Cone Part Number

 N/A LM769349X

Design Units

 N/A Imperial

Cage Type

 N/A Pin-Type
C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1 N/A 747000 lbf3320000 N
C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2 N/A 194000 lbf862000 N

Note

 N/A This part has a non-standard shoulder design. Please email customer CAD for shoulder details to ensure the proper design of mating components.

Dimensions

d - Cone Bore

 N/A 17.0000 in431.800 mm

B - Cone Width

 N/A 3.5313 in89.695 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius3 N/A 0.310 in7.900 mm

da - Cone Frontface Backing Diameter

 N/A 17.83 in453 mm

db - Cone Backface Backing Diameter

 N/A 18.35 in466 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.23 in5.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.31 in7.9 mm
a - Effective Center Location4 N/A 0.87 in22.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)5 N/A 111000 lbf495000 N
C1 - Dynamic Radial Rating (1 million revolutions)6 N/A 429000 lbf1910000 N

C0 - Static Radial Rating

 N/A 929000 lbf4130000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)7 N/A 83500 lbf371000 N

Factors

K - Factor8 N/A 1.33

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 5114.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 614.2
Cg - Geometry Factor9 N/A 0.243
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These maximum fillet radii will be cleared by the bearing corners.
  • 4 Negative value indicates effective center inside cone backface.
  • 5 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 6 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 7 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.