All Product Types > ENGINEERED BEARINGS > Tapered Roller Bearings > Tapered Roller Bearings - Single Cones > Tapered Roller Bearings - Single Cones - Imperial > Part Number M246942  

Part Number M246942, Tapered Roller Bearings - Single Cones - Imperial

    Download PDF Download PDF   
    border="0" Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.




Specifications  · Dimensions  · Abutment and Fillet Dimensions  · Basic Load Ratings  · Factors

Specifications

Cone Part Number
M246942

Design Units
Imperial

Cage Type
Stamped Steel

C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1
309000 lbf
1370000 N

C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2
80000 lbf
356000 N
1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.


Dimensions

d - Cone Bore
9.1250 in
231.775 mm

B - Cone Width
2.5625 in
65.088 mm


Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1
0.25 in
6.35 mm

da - Cone Frontface Backing Diameter
9.8 in
249 mm

db - Cone Backface Backing Diameter
10.16 in
258 mm

Ab - Cage-Cone Frontface Clearance
0.18 in
4.6 mm

Aa - Cage-Cone Backface Clearance
0.17 in
4.3 mm

a - Effective Center Location2
-0.19 in
-4.8 mm
1 These maximum fillet radii will be cleared by the bearing corners.
2 Negative value indicates effective center inside cone backface.


Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)1
46000 lbf
204000 N

C1 - Dynamic Radial Rating (1 million revolutions)2
177000 lbf
789000 N

C0 - Static Radial Rating
352000 lbf
1570000 N

Ca90 - Dynamic Thrust Rating (90 million revolutions)3
26200 lbf
116000 N
1 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
2 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.


Factors

K - Factor1
1.76

G1 - Heat Generation Factor (Roller-Raceway)
1350

G2 - Heat Generation Factor (Rib-Roller End)
198

Cg - Geometry Factor2
0.144
1 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
2 Geometry constant for Lubrication Life Adjustment Factor a3l.



 DOWNLOADS 

Tapered Roller Bearing Engineering Information
(PDF, 663KB)

Bearing Life Calculation Tool

Bearing Dimensional Tolerances