Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 00000

Cone Part Number

 N/A 00050

Cup Part Number

 N/A 00152

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1/2 in12.7 mm

D - Cup Outer Diameter

 N/A 1.5 in38.1 mm

B - Cone Width

 N/A 0.5540 in14.072 mm

C - Cup Width

 N/A 0.5337 in13.556 mm

T - Bearing Width

 N/A 0.5408 in13.736 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 0.65 in16.5 mm

db - Cone Backface Backing Diameter

 N/A 0.75 in19 mm

Da - Cup Frontface Backing Diameter

 N/A 1.40 in35.56 mm

Db - Cup Backface Backing Diameter

 N/A 1.30 in33.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.03 in-0.8 mm
a - Effective Center Location3 N/A -0.2 in-5.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 1220 lbf5410 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 4690 lbf20900 N

C0 - Static Radial Rating

 N/A 3840 lbf17100 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 574 lbf2550 N

Factors

K - Factor7 N/A 2.12
e - ISO Factor8 N/A 0.28
Y - ISO Factor9 N/A 2.18
Cg - Geometry Factor10 N/A 0.033
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.