Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 05000

Cone Part Number

 N/A 05062

Cup Part Number

 N/A 05175

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 5/8 in15.875 mm

D - Cup Outer Diameter

 N/A 1.7500 in44.450 mm

B - Cone Width

 N/A 0.5662 in14.381 mm

C - Cup Width

 N/A 0.4500 in11.430 mm

T - Bearing Width

 N/A 0.6100 in15.494 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 0.83 in21 mm

db - Cone Backface Backing Diameter

 N/A 0.93 in23.5 mm

Da - Cup Frontface Backing Diameter

 N/A 1.67 in42.40 mm

Db - Cup Backface Backing Diameter

 N/A 1.50 in38.10 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.01 in-0.3 mm
a - Effective Center Location3 N/A -0.16 in-4.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 1560 lbf6930 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 6010 lbf26700 N

C0 - Static Radial Rating

 N/A 5720 lbf25400 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 952 lbf4230 N

Factors

K - Factor7 N/A 1.64
e - ISO Factor8 N/A 0.36
Y - ISO Factor9 N/A 1.68

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 5.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 5.5
Cg - Geometry Factor10 N/A 0.0448
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.