Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 08000

Cone Part Number

 N/A 08118

Cup Part Number

 N/A 08231

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 08118-90010

Dimensions

d - Bore

 N/A 1 3/16 in30.163 mm

D - Cup Outer Diameter

 N/A 2.3125 in58.738 mm

B - Cone Width

 N/A 0.5937 in15.080 mm

C - Cup Width

 N/A 0.4219 in10.716 mm

T - Bearing Width

 N/A 0.5781 in14.684 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.04 in1.02 mm

da - Cone Frontface Backing Diameter

 N/A 1.38 in35 mm

db - Cone Backface Backing Diameter

 N/A 1.63 in41.5 mm

Da - Cup Frontface Backing Diameter

 N/A 2.20 in55.88 mm

Db - Cup Backface Backing Diameter

 N/A 2.05 in52.07 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.02 in0.5 mm
a - Effective Center Location3 N/A -0.05 in-1.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 1850 lbf8220 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 7130 lbf31700 N

C0 - Static Radial Rating

 N/A 7880 lbf35000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1500 lbf6670 N

Factors

K - Factor7 N/A 1.23
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 10.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 10.6
Cg - Geometry Factor10 N/A 0.0601
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.