Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 12500

Cone Part Number

 N/A 12580

Cup Part Number

 N/A 12520

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 0.8125 in20.638 mm

D - Cup Outer Diameter

 N/A 1.9380 in49.225 mm

B - Cone Width

 N/A 0.7813 in19.845 mm

C - Cup Width

 N/A 0.6250 in15.875 mm

T - Bearing Width

 N/A 0.7813 in19.845 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.520 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 1.02 in26 mm

db - Cone Backface Backing Diameter

 N/A 1.12 in28.5 mm

Da - Cup Frontface Backing Diameter

 N/A 1.81 in45.97 mm

Db - Cup Backface Backing Diameter

 N/A 1.67 in42.42 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.01 in0.3 mm
a - Effective Center Location3 N/A -0.28 in-7.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2540 lbf11300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 9810 lbf43600 N

C0 - Static Radial Rating

 N/A 9720 lbf43200 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1410 lbf6260 N

Factors

K - Factor7 N/A 1.81
e - ISO Factor8 N/A 0.32
Y - ISO Factor9 N/A 1.86

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 8.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 6.21
Cg - Geometry Factor10 N/A 0.0495
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.