Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 155

Cone Part Number

 N/A 157

Cup Part Number

 N/A 153

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 0.7874 in20 mm

D - Cup Outer Diameter

 N/A 2.0472 in51.999 mm

B - Cone Width

 N/A 0.6380 in16.205 mm

C - Cup Width

 N/A 0.5900 in14.986 mm

T - Bearing Width

 N/A 0.5905 in14.999 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.040 in1.020 mm
r - Cup Backface "To Clear" Radius2 N/A 0.04 in1.02 mm

da - Cone Frontface Backing Diameter

 N/A 1.02 in26 mm

db - Cone Backface Backing Diameter

 N/A 1.02 in26 mm

Da - Cup Frontface Backing Diameter

 N/A 1.89 in48.01 mm

Db - Cup Backface Backing Diameter

 N/A 1.77 in44.96 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.02 in-0.5 mm
a - Effective Center Location3 N/A -0.19 in-4.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2190 lbf9720 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 8430 lbf37500 N

C0 - Static Radial Rating

 N/A 8690 lbf38700 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1180 lbf5250 N

Factors

K - Factor7 N/A 1.85
e - ISO Factor8 N/A 0.32
Y - ISO Factor9 N/A 1.9

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 8.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 6.6
Cg - Geometry Factor10 N/A 0.0482
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.