Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 17000

Cone Part Number

 N/A 17098

Cup Part Number

 N/A 17244A

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 0.9835 in24.981 mm

D - Cup Outer Diameter

 N/A 2.4402 in61.981 mm

B - Cone Width

 N/A 0.6522 in16.566 mm

C - Cup Width

 N/A 0.5625 in14.288 mm

T - Bearing Width

 N/A 0.6300 in16.002 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 1.2 in30.5 mm

db - Cone Backface Backing Diameter

 N/A 1.30 in33.0 mm

Da - Cup Frontface Backing Diameter

 N/A 2.26 in57.40 mm

Db - Cup Backface Backing Diameter

 N/A 2.13 in54.10 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.1 in2.5 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.02 in-0.5 mm
a - Effective Center Location3 N/A -0.14 in-3.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2520 lbf11200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 9720 lbf43200 N

C0 - Static Radial Rating

 N/A 9910 lbf44100 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1650 lbf7340 N

Factors

K - Factor7 N/A 1.53
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.57

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 11.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 7.5
Cg - Geometry Factor10 N/A 0.0579
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.