Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 23600

Cone Part Number

 N/A 23690

Cup Part Number

 N/A 23621

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 3/8 in34.925 mm

D - Cup Outer Diameter

 N/A 2.8750 in73.025 mm

B - Cone Width

 N/A 1.0620 in26.975 mm

C - Cup Width

 N/A 0.8750 in22.225 mm

T - Bearing Width

 N/A 1.0626 in26.990 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 1.65 in42.1 mm

db - Cone Backface Backing Diameter

 N/A 1.93 in49 mm

Da - Cup Frontface Backing Diameter

 N/A 2.72 in68.10 mm

Db - Cup Backface Backing Diameter

 N/A 2.48 in62.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.05 in1.3 mm
a - Effective Center Location3 N/A -0.32 in-8.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 5210 lbf23200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 20100 lbf89400 N

C0 - Static Radial Rating

 N/A 22900 lbf102000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3300 lbf14700 N

Factors

K - Factor7 N/A 1.58
e - ISO Factor8 N/A 0.37
Y - ISO Factor9 N/A 1.62

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 24.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 10.7
Cg - Geometry Factor10 N/A 0.0734
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.