Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 2300

Cone Part Number

 N/A 2380

Cup Part Number

 N/A 2320

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7/8 in22.225 mm

D - Cup Outer Diameter

 N/A 2.2400 in56.896 mm

B - Cone Width

 N/A 0.9750 in24.765 mm

C - Cup Width

 N/A 0.8125 in20.638 mm

T - Bearing Width

 N/A 0.9377 in23.818 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.760 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 1.08 in27.5 mm

db - Cone Backface Backing Diameter

 N/A 1.1 in28 mm

Da - Cup Frontface Backing Diameter

 N/A 2.11 in53.10 mm

Db - Cup Backface Backing Diameter

 N/A 1.85 in46.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.03 in-0.8 mm
a - Effective Center Location3 N/A -0.37 in-9.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 3710 lbf16500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 14300 lbf63700 N

C0 - Static Radial Rating

 N/A 13900 lbf62000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1470 lbf6550 N

Factors

K - Factor7 N/A 2.52
e - ISO Factor8 N/A 0.23
Y - ISO Factor9 N/A 2.59

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 13.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 5.9
Cg - Geometry Factor10 N/A 0.0517
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.