Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 25500

Cone Part Number

 N/A 25583

Cup Part Number

 N/A 25520

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 3/4 in44.45 mm

D - Cup Outer Diameter

 N/A 3.2650 in82.931 mm

B - Cone Width

 N/A 1.4125 in35.878 mm

C - Cup Width

 N/A 0.7500 in19.050 mm

T - Bearing Width

 N/A 1.3500 in34.290 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.15 in3.80 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 1.97 in50 mm

db - Cone Backface Backing Diameter

 N/A 2.56 in65 mm

Da - Cup Frontface Backing Diameter

 N/A 3.05 in77.00 mm

Db - Cup Backface Backing Diameter

 N/A 2.91 in73.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.43 in10.9 mm
a - Effective Center Location3 N/A -0.66 in-16.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 5270 lbf23500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 20300 lbf90500 N

C0 - Static Radial Rating

 N/A 24900 lbf111000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3020 lbf13500 N

Factors

K - Factor7 N/A 1.74
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.79

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 35.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 14.3
Cg - Geometry Factor10 N/A 0.0801
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.