Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 2500

Cone Part Number

 N/A 2578

Cup Part Number

 N/A 2530

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 1/8 in28.575 mm

D - Cup Outer Diameter

 N/A 2.6150 in66.421 mm

B - Cone Width

 N/A 0.9983 in25.357 mm

C - Cup Width

 N/A 0.8125 in20.638 mm

T - Bearing Width

 N/A 1.0000 in25.400 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 1.38 in35 mm

db - Cone Backface Backing Diameter

 N/A 1.54 in39 mm

Da - Cup Frontface Backing Diameter

 N/A 2.48 in62.99 mm

Db - Cup Backface Backing Diameter

 N/A 2.36 in59.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.02 in0.5 mm
a - Effective Center Location3 N/A -0.34 in-8.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 4880 lbf21700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 18800 lbf83700 N

C0 - Static Radial Rating

 N/A 21200 lbf94400 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 2280 lbf10200 N

Factors

K - Factor7 N/A 2.14
e - ISO Factor8 N/A 0.27
Y - ISO Factor9 N/A 2.19

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 23.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 9.6
Cg - Geometry Factor10 N/A 0.0656
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.