Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 28000

Cone Part Number

 N/A 28156

Cup Part Number

 N/A 28317

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1.5740 in39.980 mm

D - Cup Outer Diameter

 N/A 3.1510 in80.035 mm

B - Cone Width

 N/A 0.7736 in19.649 mm

C - Cup Width

 N/A 0.6250 in15.875 mm

T - Bearing Width

 N/A 0.7930 in20.142 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 1.77 in45 mm

db - Cone Backface Backing Diameter

 N/A 1.93 in49 mm

Da - Cup Frontface Backing Diameter

 N/A 2.91 in73.90 mm

Db - Cup Backface Backing Diameter

 N/A 2.72 in69.09 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.01 in0.3 mm
a - Effective Center Location3 N/A -0.14 in-3.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 4390 lbf19500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 16900 lbf75200 N

C0 - Static Radial Rating

 N/A 15500 lbf68900 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3020 lbf13400 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 20.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 12.5
Cg - Geometry Factor10 N/A 0.0709
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.